/*=======================================================
20x4字符液晶主程序,编译软件(ICCAVR_6.31)
CPU内部晶振8M
数据线B0~B7接PORTB, E=D7 RW=D6 RS=D5
=========================================================
接线图如下:
_______________ ______________
| --1|GND |
| --2|+5V |
| --3|V0 |
| | |
PD5|--------4|RS |
PD6|--------5|RW |
PD7|--------6|E |
CPU | | |
ATmmega16L PB0|--------7|D0 LCD20x4 |
PB1|--------8|D1 |
PB2|--------9|D2 |
PB3|-------10|D3 |
PB4|-------11|D4 |
PB5|-------12|D5 |
PB6|-------13|D6 |
PB7|-------14|D7 |
| | |
| --15|+LED |
| --16|-LED |
_______________| |______________|
========================================================*/
#i nclude<ioM16V.h> //CPU_ATmmega16L
#define RS_H asm("sbi 0x12,5") //RS设为高电平
#define RS_L asm("cbi 0x12,5") //RS设为低电平
#define RW_H asm("sbi 0x12,6") //RW设为高电平
#define RW_L asm("cbi 0x12,6") //RW设为低电平
#define E_H asm("sbi 0x12,7") //E设为高电平
#define E_L asm("cbi 0x12,7") //E设为低电平
//=======================================================
//微秒级延时程序
void delay_us(int time)
{
do
{
time--;
}
while (time > 1);
}
//=======================================================
//毫秒级延时程序
void delay_ms(unsigned int time)
{
while(time != 0)
{
delay_us(1000);
time--;
}
}
//=======================================================
//读取lcd是否内部操作(忙碌)状态
char Lcd_Busy()
{
char r;
DDRB = 0x00; //端口B设为输入方式
E_L;RS_L;RW_H; //E=0(致能),RS=0(命令),RW=1(读)
delay_us(2); //液晶延时子程序
E_H;
delay_us(2); //液晶延时子程序
r = PINB & 0x80; //读取lcd_data第八位
E_L;
DDRB=0xff; //端口B设为输出方式
return r; //读取结果返回
}
//=======================================================
//向Lcd发送命令程序
void Lcd_Command(unsigned char Command)
{
while(Lcd_Busy()); //判断lcd是否内部操作状态
E_L;RS_L;RW_L; //E=0(致能),RS=0(命令),RW=0(写)
delay_us(2); //液晶延时子程序
E_H;
PORTB = Command; //向Lcd发送命令
delay_us(2); //液晶延时子程序
E_L;
}
//=======================================================
//向lcd写入一个字符程序
void Lcd_Write(unsigned char Data)
{
while(Lcd_Busy()); //判断lcd是否内部操作状态
E_L;RS_H;RW_L; //E=0(致能),RS=1(数据),RW=0(写)
delay_us(2); //液晶延时子程序
E_H;
PORTB = Data; //向lcd写入一个字符
delay_us(2); //液晶延时子程序
E_L;
}
/*=======================================================
LCD第1行显示地址1~20(0x80~0x93)
[1] [2] 下一页
本文关键字:单片机 源程序 AVR单片机,单片机-工控设备 - AVR单片机