1335 lcd显示C程序

      WriteOneWork(6,70,xh2);
      WriteOneWork(6,72,dha3);

      WriteOneWork(9,56,pm6);       // 剪切数量
      WriteOneWork(9,58,pm7);
      WriteOneWork(9,60,xu);
      WriteOneWork(9,62,lang);
      WriteOneWork(9,64,dha3);

      WriteOneWork(12,48,dang);    //当前量数
      WriteOneWork(12,50,qan);
      WriteOneWork(12,52,xu);
      WriteOneWork(12,54,lang);
      WriteOneWork(12,56,dha3);

      /////////--------------

      WriteOneWork(15,40,qen);     //欠预计产量数
      WriteOneWork(15,42,yi);
      WriteOneWork(15,44,jji);
      WriteOneWork(15,46,chan);
      WriteOneWork(15,48,lang);
      WriteOneWork(15,50,xu);
      WriteOneWork(15,52,dha3);


      for(uu=30;uu<70;uu++)      //---------------------
       {
        kk(18,uu,gang);
       // delay(10000);
        }


      WriteOneWork(21,24,yi); //40   //预计总工时
      WriteOneWork(21,26,jji);
      WriteOneWork(21,28,zong);
      WriteOneWork(21,30,duong);
      WriteOneWork(21,32,he);
      WriteOneWork(21,34,dha3);

      WriteOneWork(24,56,ei);      //已耗总工时
      WriteOneWork(24,58,hao);
      WriteOneWork(24,60,duong);
      WriteOneWork(24,62,he);
      WriteOneWork(24,64,dha3);
                                   //预计还需工时
      WriteOneWork(27,48,yi);
      WriteOneWork(27,50,jji);
      WriteOneWork(27,52,han);
      WriteOneWork(27,54,xie);
      WriteOneWork(27,56,duong);
      WriteOneWork(27,58,he);
      WriteOneWork(27,60,dha3);

      WriteOneWork(30,40,lai);     //累加产量
      WriteOneWork(30,42,jji);
      WriteOneWork(30,44,chan);
      WriteOneWork(30,46,lang);
      WriteOneWork(30,48,dha3);




      for(uu=31;uu<71;uu++)       //--------------
       {
        kk(33,uu,gang);
        //delay(20000);
        }

     //  for(uu=39;uu<79;uu++)
      // {
     //   kk(35,uu,fh);
     //  delay(2000);
     //  }

        while(1)
        {
           for(uu=39;uu<79;uu++)    //显示》》》》》》》》
       {
        kk(35,uu,fh);
       delay(200);
       }
           for(uu=39;uu<79;uu++)  //关》》》》》》》》》》
       {
        kk(35,uu,kong);
       //delay(2000);
       }
     //  KEYD=GetKeyStatus();
       for(sy=0;sy<10;sy++)
       {

       // kk(35,50,kong);
       //delay(2000);
      // bScanKey=1;

       kk(30,49,suzi[sy]);
       delay(40000);
       //kk(35,50,kong);
       //while(1);
        }
      }
      }
/******************************** 初始化LCD函数
********************************/
void Initialize(void)
{
        uint i;

        LcdCommand(0x40);       /* LCD SYSTEM SET系统设置令,8个参数 */

        LcdDataWrite(0x30);     //P1=（DR=IV=1=W/S=M2=M1=M0=0）

        LcdDataWrite(0x87);     //P2=（WF=1）FX=111‘B驱动方工和字体宽度

        LcdDataWrite(0x07);     //字符高度设置

        LcdDataWrite(39);       /* 显示域长度为320dot */

        LcdDataWrite(0x36);     /* 确定液晶工作频率 */

        LcdDataWrite(239);      /* 显示屏高度为240dot */

        LcdDataWrite(40);       /* 显示屏一行所占显示缓冲区字节数(L) */

        LcdDataWrite(0);        /* 显示屏一行所占显示缓冲区字节数(H) */
         delay(1000);

        LcdCommand(0x44);       /*LCD SCROLL显示区设置命令,最多10个参数*/

        LcdDataWrite(0x00);     /* 显示1区对应的显示RAM起始高8位地址 */

上一页  [1] [2] [3] [4] [5] [6] [7] [8]  下一页

本文关键字：程序  51单片机，单片机-工控设备 - 51单片机